SubscribeConfig.Builder

Builder

public Builder ()

build

public SubscribeConfig build ()

Build SubscribeConfig given the current requests made on the builder.

setInstantCommunicationModeEnabled

public SubscribeConfig.Builder setInstantCommunicationModeEnabled (boolean enabled, 
                int band)

Configure whether to enable and use instant communication for this subscribe session. Instant communication will speed up service discovery and any data-path set up as part of this session. Use Characteristics.isInstantCommunicationModeSupported() to check if the device supports this feature.

Note: due to increased power requirements of this mode - it will only remain enabled for 30 seconds from the time the discovery session is started.

setMatchFilter

public SubscribeConfig.Builder setMatchFilter (List<byte[]> matchFilter)

The match filter for a subscribe session. Used to determine whether a service discovery occurred - in addition to relying on the service name.

Optional. Empty by default.

setMaxDistanceMm

public SubscribeConfig.Builder setMaxDistanceMm (int maxDistanceMm)

Configure the maximum distance to a discovered publisher at which to trigger a discovery notification. I.e. discovery will be triggered if we've found a matching publisher (based on the other criteria in this configuration) and the distance to the publisher is smaller than the value specified in this API. Can be used in conjunction with setMinDistanceMm(int) to specify a geofence, i.e. discovery with min <= distance <= max.

For ranging to be used in discovery it must also be enabled on the publisher using PublishConfig.Builder.setRangingEnabled(boolean). However, ranging may not be available or enabled on the publisher or may be temporarily disabled on either subscriber or publisher - in such cases discovery will proceed without ranging.

When ranging is enabled and available on both publisher and subscriber and a service is discovered based on geofence constraints the DiscoverySessionCallback.onServiceDiscoveredWithinRange(PeerHandle, byte[], List, int) is called, otherwise the DiscoverySessionCallback.onServiceDiscovered(PeerHandle, byte[], List) is called.

The device must support Wi-Fi RTT for this feature to be used. Feature support is checked as described in android.net.wifi.rtt.

setMinDistanceMm

public SubscribeConfig.Builder setMinDistanceMm (int minDistanceMm)

Configure the minimum distance to a discovered publisher at which to trigger a discovery notification. I.e. discovery will be triggered if we've found a matching publisher (based on the other criteria in this configuration) and the distance to the publisher is larger than the value specified in this API. Can be used in conjunction with setMaxDistanceMm(int) to specify a geofence, i.e. discovery with min <= distance <= max.

For ranging to be used in discovery it must also be enabled on the publisher using PublishConfig.Builder.setRangingEnabled(boolean). However, ranging may not be available or enabled on the publisher or may be temporarily disabled on either subscriber or publisher - in such cases discovery will proceed without ranging.

When ranging is enabled and available on both publisher and subscriber and a service is discovered based on geofence constraints the DiscoverySessionCallback.onServiceDiscoveredWithinRange(PeerHandle, byte[], List, int) is called, otherwise the DiscoverySessionCallback.onServiceDiscovered(PeerHandle, byte[], List) is called.

The device must support Wi-Fi RTT for this feature to be used. Feature support is checked as described in android.net.wifi.rtt.

setPairingConfig

public SubscribeConfig.Builder setPairingConfig (AwarePairingConfig config)

Set the AwarePairingConfig for this subscribe session, the peer can use this info to determine the config of the following bootstrapping, pairing setup/verification request.

setServiceName

public SubscribeConfig.Builder setServiceName (String serviceName)

Specify the service name of the subscribe session. The actual on-air value is a 6 byte hashed representation of this string.

The Service Name is a UTF-8 encoded string from 1 to 255 bytes in length. The only acceptable single-byte UTF-8 symbols for a Service Name are alphanumeric values (A-Z, a-z, 0-9), the hyphen ('-'), the period ('.') and the underscore ('_'). All valid multi-byte UTF-8 characters are acceptable in a Service Name.

Must be called - an empty ServiceName is not valid.

setServiceSpecificInfo

public SubscribeConfig.Builder setServiceSpecificInfo (byte[] serviceSpecificInfo)

Specify service specific information for the subscribe session. This is a free-form byte array available to the application to send additional information as part of the discovery operation - i.e. it will not be used to determine whether a publish/subscribe match occurs.

Optional. Empty by default.

setSubscribeType

public SubscribeConfig.Builder setSubscribeType (int subscribeType)

Sets the type of the subscribe session: active (subscribe packets are transmitted over-the-air), or passive (no subscribe packets are transmitted, a match is made against a solicited/active publish session whose packets are transmitted over-the-air).

setTerminateNotificationEnabled

public SubscribeConfig.Builder setTerminateNotificationEnabled (boolean enable)

Configure whether a subscribe terminate notification DiscoverySessionCallback.onSessionTerminated() is reported back to the callback.

setTtlSec

public SubscribeConfig.Builder setTtlSec (int ttlSec)

Sets the time interval (in seconds) an active ( SubscribeConfig.Builder.setSubscribeType(int)) subscribe session will be alive - i.e. broadcasting a packet. When the TTL is reached an event will be generated for DiscoverySessionCallback.onSessionTerminated().

Optional. 0 by default - indicating the session doesn't terminate on its own. Session will be terminated when DiscoverySession.close() is called.